Drivers Extron CTR 8 Control Module


Download Now
Extron CTR 8 Control Module Driver

User Guide Switcher Accessories CTR 8 Eight Input Contact Closure to RS Control Module Rev. A 12 13 Safety Instructions Safety Instructions. View and Download Extron electronics CTR 8 setup manual online. Closure Control Module. CTR 8 Controller pdf manual download. The Extron CTR 8 provides contact closure input switching for most Extron switchers with CTR 8. Power LED — Lights green when the unit is receiving power. 1 screw connector, as shown below, to control the CTR 8 using SIS commands.


Type: Driver
Rating:
3.74
33 (3.74)
Downloads: 248
File Size: 18.81Mb
Supported systems: Windows Vista (32/64-bit), Windows XP (32/64-bit), Windows 8, Windows 10
Price: Free* [*Free Registration Required]

Download Now
Extron CTR 8 Control Module Driver

Extron Electronics CTR 8 Setup Manual

This symbol,when used on the product, is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment. Dieses Symbol auf dem Produkt soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung Extron CTR 8 Control Module Wartung Instandhaltung geben. The Class A limits provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

Extron CTR 8 Control Module Treiber Windows 7

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful Extron CTR 8 Control Module to radio communications. Operation of this equipment in a residential area is likely to cause interference; the user must correct the interference at his own expense. Shielded cables must be used to ensure compliance with FCC emissions limits.

Trademarks All trademarks mentioned in this guide are the properties of their respective owners. Attention indicates a situation that may damage or destroy the product or associated equipment. A note draws attention to important information.

Extron CTR 8 Control Module Drivers for Windows Mac

Software Commands Commands are written in the fonts shown here: From the File menu, select New. Click the OK button. Specifications Availability Product specifications are available on the Extron website, www.

Extron CTR 8 Control Module Drivers for Windows XP

It allows simple push-buttons to remotely switch and mute audio and video sources. The CTR 8 accepts up to eight contact closure inputs Extron CTR 8 Control Module converts them to SIS serial commands that select the corresponding input on an Extron switcher. The following section covers rear panel features and cabling procedures. C GTurn Tx Goff and unplug their power cords. Power Supply Output Cord Figure 3. Follow the same pin diagram above to connect a device to the Power Out connector.

EXTRON ELECTRONICS CTR 8 SETUP MANUAL Pdf Download.

If it is any longer, the Extron CTR 8 Control Module wires may touch, Extron CTR 8 Control Module a short circuit between them. If it is any shorter, the wires can be easily pulled out even if tightly fastened by the captive screws. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product. The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location, Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk.

The power supply shall not be permanently fixed to building structure or similar structure.

Wire each connector as shown in figure 4. Momentary closure of this pin to ground selects the corresponding number input.

Extron electronic Extron Electronics Switch CTR 8 User's Manual

Selection is triggered specifically at the moment of closing, not opening. When an input is Ground G selected, only the tally corresponding to that input is active. Determine and select the appropriate current-limiting resistor, if needed.

Some button switches have the resistor built in. The host device is connected to the 3-pole captive screw connector on the rear panel. The protocol is baud, 8 data bit, 1 stop bit, and no parity.

No special characters are required to begin or end a command sequence. When the CTR 8 determines that a command is valid, it executes the command and sends a response to the host device.

  • Ask a Question

CTR 8-Initiated Messages When a local event such as a change in signal status takes place, the CTR 8 sends a message to the host, indicating Extron CTR 8 Control Module status change. No response is required from the host. When the CTR 8 is first switched on, it sends the message: Unless otherwise indicated, commands are not case-sensitive.

This feature allows users to press the selected input button to mute and unmute the audio and video as needed during a presentation.

Related Drivers